HRP-N3 - серия источников питания с максимальной пиковой мощностью в 350% от MEAN WELL

Datasheet Texas Instruments OPA111AM — Даташит

ПроизводительTexas Instruments
СерияOPA111
МодельOPA111AM
Datasheet Texas Instruments OPA111AM

Малошумящий прецизионный операционный усилитель Difet 8-TO-99

Datasheets

Low Noise Precision Difet® Operational Amplifier datasheet
PDF, 150 Кб, Файл опубликован: 27 сен 2000
Выписка из документа

Цены

17 предложений от 17 поставщиков
Operational Amplifier, Single, 1 Amplifier, 2MHz, 2V/µs, ± 5V to ± 18V, TO-99, 8Pins
EIS Components
Весь мир
OPA111AM
Texas Instruments
1 776 ₽
T-electron
Россия и страны СНГ
OPA111AM
Texas Instruments
2 570 ₽
OPA111AM/BM/SM/AM-3
Texas Instruments
по запросу
МосЧип
Россия
OPA111AM-BM
Texas Instruments
по запросу
Выбираем схему BMS для заряда литий-железофосфатных (LiFePO4) аккумуляторов

Статус

Статус продуктаNRND (Не рекомендуется для новых разработок)
Доступность образцов у производителяНет

Корпус / Упаковка / Маркировка

Pin8
Package TypeLMC
Industry STD TermTO-CAN
JEDEC CodeO-MBCY-W
Package QTY20
CarrierTUBE
МаркировкаOPA111AM
Width (мм)9.08
Length (мм)9.08
Thickness (мм)4.4
Pitch (мм)2.54
Max Height (мм)5.72
Mechanical DataСкачать

Экологический статус

RoHSСовместим

Application Notes

  • Noise Analysis of FET Transimpedance Amplifiers
    PDF, 97 Кб, Файл опубликован: 2 окт 2000
    The availability of detailed noise spectral density characteristics for the OPA111 amplifier allows an accurate noise error analysis in a variety of different circuit configurations. The fact that the spectral characteristics are guaranteed maximums allows absolute noise errors to be truly bounded.
  • Feedback Circuit Clamps Precisely
    PDF, 26 Кб, Файл опубликован: 27 сен 2000
    A limiter circuit consisting of an input buffer (A1), an output-scaling amplifier (A2), two zener diodes (Z1 and Z2), and several other components can supply sharp, precise, bipolar clamp levels with continuous variable control, from 0 to В±11V. A feedback loop enclosing the amplifiers and zeners generates the high clamping accuracy.
  • Feedback Plots Define Op Amp AC Performance
    PDF, 89 Кб, Файл опубликован: 27 сен 2000
    Feedback plots simplify the analysis of an op amp's closed-loop AC performance by showing bandwidth and stability conditions as a function of the op amp's gain and phase response. These plots also provide insight into noise performance and the special feedback requirements of circuits such as integrating converters, photodiode amplifiers, composite amplifiers and active feedback circuits.
  • Diode-Connected FET Protects Op Amps
    PDF, 49 Кб, Файл опубликован: 2 окт 2000
    Providing input-overload protection for sensitive measurement circuits proves difficult when you must not degrade the circuits? performance in the process. It?s an especially tricky problem when you?re measuring a material?s dielectric properties. In such an application, an ultra-low input bias current op amp serves as a current integrator to measure a dielectric?s response to a 100V step.
  • Comparison of Noise Performance of FET Transimpedence Amp/Switched Integrator
    PDF, 66 Кб, Файл опубликован: 27 сен 2000
    Low-input current FET operational amplifiers are universlly used to monitor photodetector, or more commonly photodiode currents. These photodetectors bridge the gap between a physical event, light, and electronics. There are a variey of amplifier configurations to select from and the choice is based on noise, bandwidth, offset, and linearity. A considerable amount has been written on the performan
  • Implementation and Applications of Current Sources and Current Receivers
    PDF, 427 Кб, Файл опубликован: 27 сен 2000
    This application guide is intended as a source book for the design and application of: Current sourcesCurrent sinksFloating current sourcesVoltage-to-current converters(transconductance amplifiers)Current-to-current converters (current mirrors)Current-to-voltage converters(transimpedance amplifiers)
  • Compensate Transimpedance Amplifiers Intuitively (Rev. A)
    PDF, 69 Кб, Версия: A, Файл опубликован: 30 мар 2005
    Transimpedance amplifiers are used to convert low-level photodiode currents to usable voltage signals. All too often, the amplifiers have to be empirically compensated to operate properly. The problem can be easily understood if one looks at all the elements involved.
  • Tuning in Amplifiers
    PDF, 44 Кб, Файл опубликован: 2 окт 2000
    Have you ever had the experience of designing an analog gain block with an amplifier that is specified to be unity gain stable only to find that it is oscillating out of control in your circuit? Or have you ever replaced a stable voltage feedback amplifier with a current feedback amplifier to find that the current feedback amplifier immediately oscillates when placed in the amplifier socket? Oscil
  • Op Amp Performance Analysis
    PDF, 76 Кб, Файл опубликован: 2 окт 2000
    This bulletin reflects the analysis power gained through knowledge of an op amp circuit's feedback factor. Feedback dictates the performance of an op amp both in function and in quality. The major specifications of the amplifier descibe an open-loop device awaiting feedback direction of the end circuit's function. Just how well the amplifier performs the function reflects through the feedback inte
  • Single-Supply Operation of Operational Amplifiers
    PDF, 77 Кб, Файл опубликован: 2 окт 2000
    Operation of op amps from single supply voltages is useful when negative supply voltages are not available. Furthermore, certain applications using high voltage and high current op amps can derive important benefits from single supply operation.

Модельный ряд

Серия: OPA111 (4)

Классификация производителя

  • Semiconductors > Amplifiers > Operational Amplifiers (Op Amps) > Precision Op Amps

На английском языке: Datasheet Texas Instruments OPA111AM

Электронные компоненты. Бесплатная доставка по России