LT1113 elecTrical characTerisTics The l denotes specifications which apply over the temperature range–40°C ≤ TA ≤ 85°C. VS = ±15V, VCM = 0V, unless otherwise noted. (Note 10)LT1113ACLT1113CSYMBOL PARAMETERCONDITIONS (Note 4)MINTYPMAXMINTYPMAXUNITS IS Supply Current per Amplifier l 5.30 6.35 5.30 6.55 mA VS = ±5V l 5.25 6.30 5.25 6.50 mA ∆VOS Offset Voltage Match l 1.0 4.4 1.0 5.1 mV ∆I + B Noninverting Bias Current Match l 50 600 55 900 pA ∆CMRR Common Mode Rejection Match (Note 11) l 76 93 73 93 dB ∆PSRR Power Supply Rejection Match (Note 11) l 77 92 75 92 dB The l denotes specifications which apply over the temperature range –55°C ≤ TA ≤ 125°C. VS = ±15V, VCM = 0V,unless otherwise noted. (Note 12)LT1113AMLT1113MSYMBOL PARAMETERCONDITIONS (Note 4)MINTYPMAXMINTYPMAXUNITS VOS Input Offset Voltage l 0.8 2.7 0.9 3.3 mV VS = ±5V l 0.8 2.8 0.9 3.4 mV ∆VOS Average Input Offset (Note 8) l 5 12 8 15 µV/°C ∆Temp Voltage Drift IOS Input Offset Current l 0.8 15 1.0 25 nA IB Input Bias Current l 25 50 27 70 nA VCM Input Voltage Range l 12.6 13.0 12.6 13.0 V l –10.0 –10.4 –10.0 –10.4 V CMRR Common Mode Rejection Ratio VCM = –10V to 12.6V l 79 95 77 92 dB PSRR Power Supply Rejection Ratio VS = ±4.5V to ±20V l 80 97 78 95 dB AVOL Large-Signal Voltage Gain VO = ±12V, RL = 10k l 800 2700 700 2500 V/mV VO = ±10V, RL = 1k l 400 1500 300 1000 V/mV VOUT Output Voltage Swing RL = 10k l ±13.0 ±12.5 ±12.5 ±12.5 V RL = 1k l ±11.5 ±12.0 ±11.0 ±12.0 V SR Slew Rate RL ≥ 2k (Note 9) l 1.9 3.3 1.6 3.3 V/µs GBW Gain Bandwidth Product fO = 100kHz l 2.2 3.4 2.2 3.4 MHz IS Supply Current Per Amplifier l 5.30 6.35 5.30 6.55 mA VS = ±5V l 5.25 6.30 5.25 6.50 mA ∆VOS Offset Voltage Match l 1.0 5.0 1.0 5.5 mV ∆I + B Noninverting Bias Current Match l 1.8 12 2.0 20 nA ∆CMRR Common Mode Rejection Match (Note 11) l 75 92 73 92 dB ∆PSRR Power Supply Rejection Match (Note 11) l 76 91 74 91 dB Note 1: Stresses beyond those listed under Absolute Maximum Ratings factory. The LT1113M is guaranteed to meet specified performance from may cause permanent damage to the device. Exposure to any Absolute –55°C to 125°C. Maximum Rating condition for extended periods may affect device Note 4: Typical parameters are defined as the 60% yield of parameter reliability and lifetime. distributions of individual amplifiers, i.e., out of 100 LT1113s (200 op Note 2: The LT1113C is guaranteed functional over the Operating amps) typically 120 op amps will be better than the indicated specification. Temperature Range of –40°C to 85°C. The LT1113M is guaranteed Note 5: Warmed-up IB and IOS readings are extrapolated to a chip temperature functional over the Operating Temperature Range of –55°C to 125°C. of 50°C from 25°C measurements and 50°C characterization data. Note 3: The LT1113C is guaranteed to meet specified performance from Note 6: Current noise is calculated from the formula: 0°C to 70°C. The LT1113C is designed, characterized and expected to i meet specified performance from –40°C to 85°C but is not tested or QA n = (2qIB)1/2 sampled at these temperatures. For guaranteed I grade parts, consult the where q = 1.6 • 10–19 coulomb. The noise of source resistors up to 200M swamps the contribution of current noise. 1113fc For more information www.linear.com/LT1113 5
