Радиолоцман Электроника en
расширенный поиск +

Datasheet Texas Instruments MSP430FW428IPMR

Datasheet Texas Instruments MSP430FW428IPMR

ПроизводительTexas Instruments

MSP430FW42x Mixed Signal Microcontroller 64-LQFP -40 to 85


  • Скачать » Datasheet, PDF, 1.3 Мб, Версия: E, 17-12-2013, Файл закачен 20-03-2018
    MSP430FW42x Mixed Signal Microcontroller datasheet
    Выписка из документа ↓
    MSP430FW429, MSP430FW428
    MSP430FW427, MSP430FW425, MSP430FW423
    www.ti.com SLAS383E – OCTOBER 2003 – REVISED DECEMBER 2013 MSP430FW42x Mixed-Signal Microcontroller
    FEATURES 1 2 Low Supply Voltage Range: 1.8 V to 3.6 V
    Ultra-Low-Power Consumption:
    – Active Mode: 200 µA at 1 MHz, 2.2 V
    – Standby Mode: 0.7 µA
    – Off Mode (RAM Retention): 0.1 µA
    Five Power-Saving Modes
    Wake Up From Standby Mode in Less Than
    6 Вµs
    Frequency-Locked Loop, FLL+
    16-Bit RISC Architecture,
    125-ns Instruction Cycle Time
    Scan Interface for Background Water, Heat,
    and Gas Volume Measurement
    16-Bit Timer_A With Three Capture/Compare
    16-Bit Timer_A With Five Capture/Compare
    Integrated LCD Driver for Up to 96 Segments
    On-Chip Comparator
    Serial Onboard Programming, No External ...


    SRAM:2048Б; Flash:48кБ; 8МГц; LQFP64; Интерфейс: ESI, JTAG
    T-electronTexas Instruments231 руб.
    5 элементTexas Instrumentsпо запросу
    LifeElectronicsTexas Instrumentsпо запросу
    Кремнийпо запросу
    Подробнее об условиях поставки »

Семейство: MSP430FW423, MSP430FW425, MSP430FW427, MSP430FW428, MSP430FW429


Статус продуктаВ производстве (Рекомендуется для новых разработок)
Доступность образцов у производителяДа

Корпус / Упаковка / Маркировка

Package TypePM
Industry STD TermLQFP
Package QTY1000
CarrierLARGE T&R
Width (мм)10
Length (мм)10
Thickness (мм)1.4
Pitch (мм).5
Max Height (мм)1.6
Mechanical DataСкачать »


Active Power200 uA/MHz
Additional FeaturesLCD,Watchdog,Scan Interface,Brown Out Reset
Тактовая частота8 МГц
GPIO Pins48
Max VCC3.6
Min VCC1.8
Non-volatile Memory48 KB
Рабочий диапазон температурот -40 до 85 C
Package GroupLQFP
Package Size: mm2:W x L64LQFP: 144 mm2: 12 x 12(LQFP) PKG
Special I/ON/A
Standby Power0.7 LPM3-uA
Timers - 16-bit2
Wakeup Time6 us

Экологический статус


Комплекты разработчика и оценочные наборы

  • Evaluation Modules & Boards: MSP-FET430U64
    64-pin Target Development Board and MSP-FET Programmer Bundle - MSP430F1x, MSP430F2x, MSP430F4x MCUs
    Статус продукта: В производстве (Рекомендуется для новых разработок)
  • Evaluation Modules & Boards: MSP-TS430PM64
    MSP-TS430PM64 - 64-pin Target Development Board for MSP430F1x, MSP430F2x and MSP430F4x MCUs
    Статус продукта: В производстве (Рекомендуется для новых разработок)
  • JTAG Emulators/ Analyzers: ENERGYTRACE
    MSP EnergyTrace Technology
    Статус продукта: В производстве (Рекомендуется для новых разработок)

Application Notes

  • Скачать » Application Notes, PDF, 73 Кб, 28-02-2006
    MSP430FW42x Scan Interface SIFCLK Adjustment
  • Скачать » Application Notes, PDF, 153 Кб, 15-12-2006
    Rotary/Linear Motion Detection Using the MSP430 Scan Interface & Optical Sensors
    Rotary and Linear Motion Detection Using the MSP430 Scan Interface and Optical Sensors Application ReportThe MSP430FW42x Scan Interface module provides an innovative way of detecting rotation and movement without the need for CPU intervention. While the interface was designed with LC and GMR sensors in mind, it is also possible to use the Scan Interface with optical sensors. Complete measureme
  • Скачать » Application Notes, PDF, 611 Кб, 12-04-2013
    MSP430FW42x ScanIF Demo Box Hardware/Software Description
    This application report describes the specific information of the demo box that detects the disc rotation using Scan Interface in MSP430FW42x. Both hardware and software are covered to help the developer understand the working principle of this demo box in a short time.
  • Скачать » Application Notes, PDF, 146 Кб, 01-08-2006
    MSP430FW42x Scan Interface SIFDACR Calibration
    With this document, the user will become familiar with the features implemented in the MSP430 scan interface module relating to calibration of the SIFDACRx threshold limits for the channel input comparator control circuitry. Two methods of calibration are discussed, Text Cycle Insertion and Direct Comparator Measurement.
  • Скачать » Application Notes, PDF, 443 Кб, 18-04-2007
    Using GMR Sensors With the MSP430 Scan Interface
    The scan interface (SIF) of the MSP430F42x family of microcontrollers provides an innovative, low-power method to measure rotation that can be used with a variety of sensor types. Many sensor configurations generate a quadrature signalling sequence, but some do not. The SIF can accommodate a variety of input signals – not just quadrature.This application report describes implementation of a rota
  • Скачать » Application Notes, PDF, 104 Кб, Версия: A, 11-09-2009
    Simple Power Solution Using LDOs for the DM365 (Rev. A)
  • Скачать » Application Notes, PDF, 95 Кб, Версия: A, 06-02-2015
    Migrating From MSP430FW42x Scan Interface to MSP430FR6x8x/FR5x8x ESI (Rev. A)
    The purpose of this application report is to facilitate the migration of designs based on the MSP430FW42x Scan Interface (SIF) to the MSP430FR5xx/FR6xx Extended Scan Interface (ESI). This document describes the main differences between the two peripheral modules and provides migration solutions covering both software and hardware aspects.
  • Скачать » Application Notes, PDF, 596 Кб, 16-05-2012
    MSP430 Embedded Application Binary Interface
    This document is a specification for the ELF-based Embedded Application Binary Interface (EABI) for the MSP430 family of processors from Texas Instruments. The EABI defines the low-level interface between programs, program components, and the execution environment, including the operating system if one is present. Components of the EABI include calling conventions, data layout and addressing conve
  • Скачать » Application Notes, PDF, 2.1 Мб, Версия: A, 20-07-2015
    Designing With MSP430 and Segment LCDs (Rev. A)
    Segment liquid crystal displays (LCDs) are needed to provide information to users in a wide variety of applications from smart meters to electronic shelf labels (ESL) to medical equipment. Several MSP430в„ў microcontroller families include built-in low-power LCD driver circuitry that allows the MSP430 MCU to directly control the segmented LCD glass. This application note helps explain how segmented
  • Скачать » Application Notes, PDF, 306 Кб, 30-06-2004
    Choosing an Ultra Low-Power MCU
    This application report describes how to compare ultralow-power MCUs. It discusses the key differences between popular low-power MCUs and how to interpret features and specifications and apply them to application requirements.
  • Скачать » Application Notes, PDF, 184 Кб, 15-11-2004
    MSP430 LFXT1 Oscillator Accuracy
    This report details the factors that influence achievable accuracy of the low frequency oscillator, specifically for real-time clock (RTC) applications. The intent of this application report is to provide an understanding of MSP430-specific factors influencing real-world achievable RTC accuracy using the LFXT1 oscillator with a standard 32.768 kHz watch crystal and present measurement data support
  • Скачать » Application Notes, PDF, 49 Кб, 18-10-2000
    Simple 1.5 V Boost Converter for MSP430
    A simple, efficient, low-cost, boost converter to take 1.5 V from a single type-AA alkaline battery to the operating voltage required by the MSP430 family of ultralow-power microcontrollers is described. Expected battery life is up to 1000 hours.
  • Скачать » Application Notes, PDF, 5.5 Мб, 21-01-2000
    MSP430 Family Mixed-Signal Microcontroller Application Reports
    MSP430 Metering Application Report
  • Скачать » Application Notes, PDF, 220 Кб, 13-09-2006
    Wave Digital Filtering Using the MSP430
    Digital filtering is an integral part of many digital signal processing algorithms. Digital filters are characterized as either recursive [infinite impulse response (IIR)] or non-recursive [finite impulse response (FIR)] filters. IIR filters require a smaller order for the same set of specifications compared to FIR filters, while FIR filters provide a linear phase property. However, IIR filters, i
  • Скачать » Application Notes, PDF, 110 Кб, 14-12-1998
    FSK Modulation and Demodulation With the Microcontroller MSP430
    This application report describes a software program for performing V.23 FSK modem transceiver functions using an MSP430 microcontroller. It makes use of novel filter architecture to perform DSP functions on a processor with only shift and add capabilities.
  • Скачать » Application Notes, PDF, 125 Кб, 04-11-2004
    CRC Implementation with MSP430
    Cyclic Redundancy Code (CRC) is commonly used to determine the correctness of a data transmission or storage. This application note presents a solution to compute 16-bit and 32-bit CRCs on the ultra low-power TI MSP430 microcontroller for the bitwise algorithm (low memory, low cost) and the table-based algorithm (low MIPS, low power). Both algorithms are presented in C and MSP430 assembly. Test co
  • Скачать » Application Notes, PDF, 168 Кб, 28-02-2002
    Mixing C and Assembler with the MSP430
    This application note describes how C and assembler code can be used together within an MSP430 application. The combination of C and assembler benefits the designer by providing the power of a high-level language as well as the speed, efficiency, and low-level control of assembler.
  • Скачать » Application Notes, PDF, 39 Кб, 13-10-2006
    Random Number Generation Using the MSP430
    Many applications require the generation of random numbers. These random numbers are useful for applications such as communication protocols, cryptography, and device individualization.Generating random numbers often requires the use of expensive dedicated hardware. Using the two independent clocks available on the MSP430F2xx family of devices, it is possible to generate random numbers without s
  • Скачать » Application Notes, PDF, 104 Кб, 03-08-2006
    Efficient Multiplication and Division Using MSP430
  • Скачать » Application Notes, PDF, 770 Кб, 16-01-2008
    MSP430 Capacitive Single-Touch Sensor Design Guide
    This application report discusses the design of RC-type capacitive single-touch sensors using the MSP430 microcontroller. The MSP430 has some unique features that make it suitable for interfacing with capacitive-touch sensors. The RC-type method does not need special peripherals and can be implemented with all devices in the MSP430 product family. This method is also inherently low power and can
  • Скачать » Application Notes, PDF, 475 Кб, 27-03-2008
    Understanding MSP430 Flash Data Retention
    The MSP430 family of microcontrollers, as part of its broad portfolio, offers both read-only memory (ROM)-based and flash-based devices. Understanding the MSP430 flash is extremely important for efficient, robust, and reliable system design. Data retention is one of the key aspects to flash reliability. In this application report, data retention for the MSP430 flash is discussed in detail and the
  • Скачать » Application Notes, PDF, 134 Кб, 20-02-2002
    Implementing An Ultralow-Power Keypad Interface with MSP430
    Often in applications with keypads, the condition can occur where a key can be held or stuck down, causing excess current consmption and reducing the battery life of a battery-operated product. This application report shows a solution. The keypad interface in this report, based on the MSP430, draws .1uA while waiting for a key press, is completely interrupt driven requring no polling, and consum
  • Скачать » Application Notes, PDF, 64 Кб, 31-12-2005
    Li-Ion Battery Charger solution using the MSP430
  • Скачать » Application Notes, PDF, 421 Кб, 01-10-2002
    Interfacing the 3-V MSP430 to 5-V Circuits
    The interfacing of the 3-V MSP430x1xx and MSP430x4xx microcontroller families to circuits with a supply of 5 V or higher is shown. Input, output and I/O interfaces are given and explained. Worse-case design equations are provided, where necessary. Some simple power supplies generating both voltages are shown, too.
  • Скачать » Application Notes, PDF, 95 Кб, 29-03-2007
    Efficient MSP430 Code Synthesis for an FIR Filter
    Digital filtering can be easily accomplished on the MSP430 using efficient multiplication. The tool accompanying this document automatically converts FIR filter coefficients to MSP430 assembly code that can be used in any application. Horner’s method and CSD format is used to accomplish the efficient multiply operations. The performance of the filter on the MSP430 is shown by evaluating the gain a

Модельный ряд

Серия: MSP430FW428 (2)

Классификация производителя

  • Semiconductors > Microcontrollers (MCU) > MSP430 ultra-low-power MCUs > MSP430F2x/4x

На английском языке: Datasheet Texas Instruments MSP430FW428IPMR

Срезы ↓
DC-DC повышающий регулируемый преобразователь питания на MT3608
DC-DC регулируемый преобразователь питания
на MT3608
Входное напряжение: 2В-24В
Выходное напряжение: 4В-28В
Входной ток: 2А
Цена: от 22 руб.
Доставка: Весь мир / Россия
Астрономический для уличного освещения таймер РЭВ-225
Астрономический таймер для уличного освещения РЭВ-225
Автоматически вычисляется время восхода и заката солнца на основе введенных координат и текущего времени, позволяя управлять освещением без использования внешних датчиков.
Цена: от 1500 руб.
Доставка: Россия
Тестер аккумуляторных батарей ZB2L3
Тестер аккумуляторных батарей ZB2L3
0-15 В, 3 А, 10 тыс.А·ч, Micro USB
Цена: от 180 руб.
Доставка: Весь мир / Россия
радиолоцман вконтакте радиолоцман одноклассники радиолоцман facebook радиолоцман twitter радиолоцман google плюс