Datasheet Linear Technology LT1085 — Даташит

Datasheets

Цены

Купить LT1085 на РадиоЛоцман.Цены — от 13 до 2 159 ₽ 57 предложений от 32 поставщиков Линейный стабилизатор с низким падением напряжения положительной полярности 1.25В до 28.5В 3А
Стандарт СИЗ Россия	LT1085CT (ST-LD1085V) STMicroelectronics	13 ₽	Купить
AliExpress Весь мир	LT1085CT TO-220 LT1085 TO220 1085CT LT1083CT LT1083 1083CT LT1086CT LT1086 регулятор	25 ₽	Купить
Триема Россия	UZ1085 ( LT1085)	33 ₽	Купить
Десси Россия	Транзистор биполярный LT1085CT (3.3) STMicroelectronics	82 ₽	Купить

Корпус / Упаковка / Маркировка

Параметры

Экологический статус

Другие варианты исполнения

LT1084 LT1084

Application Notes

• Скачать
  Performance Enhancement Techniques for Three-Terminal Regulators &mdash AN2
  PDF, 975 Кб, Файл опубликован: 2 авг 1984
  This application note describes a number of enhancement circuit techniques used with existing 3-terminal regulators which extend current capability, limit power dissipation, provide high voltage output, operate from 110VAC or 220VAC without the need to switch transformer windings, and many other usefu application ideas.
  Выписка из документа

  Application Note 2
  August 1984
  Performance Enhancement Techniques for
  Three-Terminal Regulators
  Jim Williams
  Three terminal regulators provide a simple, effective solution to voltage regulation requirements. In many situations
  the regulator can be used with no special considerations.
  Some applications, however, require special techniques
  to enhance the performance of the device.
  Probably the most common modification involves extending the output current of regulators. Conceptually, the
  simplest way to do this is by paralleling devices. In practice,
  the voltage output tolerance of the regulators can cause
  problems. Figure 1 shows a way to use two regulators to
  achieve an output current equal to their sum. This circuit
  capitalizes on the 1% output tolerance of the specified
  regulators to achieve a simple paralleled configuration.
  Both regulators sense from the same divider string and
  the small value resistors provide ballast to account for the
  slightly differing output voltages. This added impedance
  degrades total circuit regulation to about 1%. Figure 2 shows another way to extend current capability
  in a regulator. Although this circuit is more complex than
  Figure 1, it eliminates the ballasting resistor’s effects
  and has a fast-acting logic-controlled shutdown feature. …

• Скачать
  Step Down Switching Regulators &mdash AN35
  PDF, 6.2 Мб, Файл опубликован: 1 авг 1989
  Discusses the LT1074, an easily applied step-down regulator IC. Basic concepts and circuits are described along with more sophisticated applications. Six appended sections cover LT1074 circuitry detail, inductor and discrete component selection, current measuring techniques, efficiency considerations and other topics.
  Выписка из документа

  Application Note 35
  August 1989
  Step-Down Switching Regulators
  Jim Williams
  lost in this voltage-to-current-to-magnetic п¬Ѓeld-to-current-to-charge-to-voltage conversion. In practice, the
  circuit elements have losses, but step-down efficiency is
  still higher than with inherently dissipative (e.g., voltage
  divider) approaches. Figure 2 feedback controls the basic
  circuit to regulate output voltage. In this case switch ontime (e.g., inductor charge time) is varied to maintain the
  output against changes in input or loading.
  REGULATED
  OUTPUT IN PULSE
  WIDTH
  MODULATOR Figure 1 is a conceptual voltage step-down or “buck”
  circuit. When the switch closes the input voltage appears
  at the inductor. Current flowing through the inductor-capacitor combination builds over time. When the switch
  IN OUT AN35 F01 Figure 1. Conceptual Voltage Step-Down (“Buck”) Circuit opens current flow ceases and the magnetic field around
  the inductor collapses. Faraday teaches that the voltage
  induced by the collapsing magnetic п¬Ѓeld is opposite to the
  originally applied voltage. As such, the inductor’s left side
  heads negative and is clamped by the diode. The capacitors accumulated charge has no discharge path, and a DC
  potential appears at the output. This DC potential is lower
  than the input because the inductor limits current during …

• Скачать
  5V to 3.3V Converters for Microprocessor Systems &mdash AN58
  PDF, 310 Кб, Файл опубликован: 1 сен 1993
  Many popular microprocessors operate from 3.3V supplies, yet they are used in systems where the predominate source of power is 5V. AN58 presents a collection of both linear and switching regulator solutions for conversion of 5V to 3.3V at currents ranging from 100mA to 20A. Applications information and a comparison of various bypass capacitor types is included. Most of the designs can be easily modified for other intermediate voltages such as 3.45V, 3.7V, and 4.1V.
  Выписка из документа

  Application Note 58
  September 1993
  5V to 3.3V Converters for Microprocessor Systems
  Robert Dobkin, Mitchell Lee, Dennis O'Neill and Milt Wilcox
  Introduction Linear Regulators The new generation of high performance microprocessors are built on dense, low breakdown voltage processes
  in order to accommodate increased transistor counts.
  These new processors require high current power at 3.3V,
  developed from the 5V input used to power the rest of the
  system. Special techniques are required to ensure proper
  operation of the microprocessor and good heat dissipation within the computer system. Table 1 shows the range of components available for linear
  regulation of 3.3V with a 5V input. With only 1.7V of
  headroom, low dropout is essential. Low dropout regulators are available delivering currents from 125mA to 7.5A,
  allowing almost any microprocessor to be powered with a
  local 3.3V generation circuit. The first four devices (LT1020,
  LT1120, LT1121 and LT1129) are PNP micropower low
  dropout regulators. Since PNP transistors are much larger
  than monolithic NPNs, higher current regulators use an
  NPN pass device. The LT1117, LT1086, LT1083 through
  LT1085, and LT1087 all use NPN pass devices. The NPN
  structure requires about 1.2V headroom compared to the
  400mV to 500mV dropout typical of PNP regulators, and
  ground current of 5mA or 10mA, independent of output
  current. Because of this constant quiescent current, the …

• Скачать
  Using the LTC1325 Battery Management IC: &mdash AN64
  PDF, 385 Кб, Файл опубликован: 2 авг 1996
  Application Note 64 details characteristics of various battery types and appropriate charging management schemes. The LTC1325 battery management IC is highlighted along with information for applying it to any type battery. Techniques and circuitry for conditioning, charging and monitoring NiCd, NiMH, Li-Ion and Lead-Acid batteries are presented.
  Выписка из документа

  Application Note 64
  August 1996
  Using the LTC1325 Battery Management IC
  Anthony Ng, Peter Schwartz, Robert Reay,
  Richard Markell
  INTRODUCTION
  For a variety of reasons, it is desirable to charge batteries
  as rapidly as possible. At the same time, overcharging
  must be limited to prolong battery life. Such limitation of
  overcharging depends on factors such as the choice of
  charge termination technique and the use of multi-rate/
  multi-stage charging schemes. The majority of battery
  charger ICs available today lock the user into one fixed
  charging regimen, with at best a limited number of
  customization options to suit a variety of application needs
  or battery types. The LTCВ®1325 addresses these shortcomings by providing the user with all the functional
  blocks needed to implement a simple but highly flexible
  battery charger (see Figure 1) which not only addresses
  the issue of charging batteries but also those of battery
  conditioning and capacity monitoring. A microprocessor
  interacts with the LTC1325 through a serial interface to
  control the operation of its functional blocks, allowing
  software to expand the scope and flexibility of the charger …

Design Notes

• Скачать
  Techniques for Deriving 3.3V from 5V Supplies &mdash DN74
  PDF, 73 Кб, Файл опубликован: 1 сен 1993
  Выписка из документа

  advertisement Techniques for Deriving 3.3V from 5V Supplies – Design Note 74
  Mitchell Lee
  Microprocessor chip sets and logic families that operate from 3.3V supplies are gaining acceptance in both
  desktop and portable computers. Computing rates, and
  in most cases, energy consumed by these circuits show
  a strong improvement over 5V technology. The main
  power supply in most systems is still 5V, necessitating
  a local 5V to 3.3V regulator.
  Linear regulators are viable solutions at lower (IO ≤ 1A)
  currents, but they must have a low dropout voltage in
  order to maintain regulation with a worst-case input
  5 4.5V TO 5.5V IN OUT 1 + LT1129-3.3
  4 SHUTDOWN SENSE 2 GND 3.3V OUT
  700mA
  3.3ОјF
  SOLID TANTALUM of only 4.5V. Figure 1 shows a circuit that converts a
  4.5V minimum input to 3.3V with an output tolerance
  of only 3% (100mV). The LTВ®1129-3.3 can handle up to
  700mA in surface mount configurations, and includes
  both 16ОјA shutdown and 50ОјA standby currents for
  system sleep modes. Unlike other linear regulators, the
  LT1129-3.3 combines both low dropout and low voltage
  operation. Small input and output capacitors facilitate …

• Скачать
  5V to 3.3V Regulator with Fail-Safe Switchover &mdash DN82
  PDF, 74 Кб, Файл опубликован: 1 май 1994
  Выписка из документа

  advertisement 5V to 3.3V Regulator with Fail-Safe Switchover – Design Note 82
  Mitchell Lee
  Newer microprocessors designed for replacing existing
  5V units operate from lower voltage supplies. In the past
  a processor swap was simply a matter of removing one
  IC and replacing it with an updated version. But now
  the upgrade path involves switching from a 5V chip to
  one that requires 3.xxV.
  One means of changing supply voltage from 5V to 3.xxV
  is to clip a jumper that bypasses a local 3.xxV regulator.
  This is not a good solution since it leaves too much to
  chance. Failure to remove the jumper can result in the
  instant destruction of the new microprocessor upon
  application of power. A means of automatically sensing
  the presence of a 3.xxV or 5V processor is necessary.
  Intel microprocessors include a special pin called
  “VOLDET” which can be used to determine whether
  or not a particular chip needs 3.xxV or 5V. Figure 1
  shows a simple circuit that takes advantage of this
  pin to automatically “jumper out” a 3.xxV regulator
  whenever a 5V processor is inserted into the socket. VOLDET is pulled low on 3.xx processors; it is buffered
  by transistor Q2 which grounds the gate of a bypassing
  switch (Q1). Q1 is turned off leaving the LTВ®1085 to …

Модельный ряд

Классификация производителя

• Power Management > LDO Linear Regulators > Positive Linear Regulators (LDO)