PROM2PROM - кабинет для закупа электронных компонентов

Datasheet ATtiny13, ATtiny13V - Summary (Microchip)

ПроизводительMicrochip
Описание8-bit AVR Microcontroller with 1K Bytes In-System Programmable Flash
Страниц / Страница22 / 1 — Features. High Performance, Low Power AVR. 8-Bit Microcontroller. …
ВерсияRev. 08-01-2010
Формат / Размер файлаPDF / 574 Кб
Язык документаанглийский

Features. High Performance, Low Power AVR. 8-Bit Microcontroller. Advanced RISC Architecture

Datasheet ATtiny13, ATtiny13V - Summary Microchip, Версия: Rev 08-01-2010

Алкалиновые батарейки POWER FLASH – новая продукция в линейке поставок Компэл

Текстовая версия документа

Features

High Performance, Low Power AVR
®
8-Bit Microcontroller

Advanced RISC Architecture – 120 Powerful Instructions – Most Single Clock Cycle Execution – 32 x 8 General Purpose Working Registers – Fully Static Operation – Up to 20 MIPS Througput at 20 MHz

High Endurance Non-volatile Memory segments – 1K Bytes of In-System Self-programmable Flash program memory – 64 Bytes EEPROM 8-bit – 64 Bytes Internal SRAM Microcontroller – Write/Erase cyles: 10,000 Flash/100,000 EEPROM – Data retention: 20 years at 85°C/100 years at 25°C (see page 6) with 1K Bytes – Programming Lock for Self-Programming Flash & EEPROM Data Security

Peripheral Features In-System – One 8-bit Timer/Counter with Prescaler and Two PWM Channels – 4-channel, 10-bit ADC with Internal Voltage Reference Programmable – Programmable Watchdog Timer with Separate On-chip Oscillator – On-chip Analog Comparator Flash

Special Microcontroller Features – debugWIRE On-chip Debug System – In-System Programmable via SPI Port ATtiny13 – External and Internal Interrupt Sources – Low Power Idle, ADC Noise Reduction, and Power-down Modes ATtiny13V – Enhanced Power-on Reset Circuit – Programmable Brown-out Detection Circuit – Internal Calibrated Oscillator

I/O and Packages Summary – 8-pin PDIP/SOIC: Six Programmable I/O Lines – 20-pad MLF: Six Programmable I/O Lines

Operating Voltage: – 1.8 - 5.5V for ATtiny13V – 2.7 - 5.5V for ATtiny13

Speed Grade – ATtiny13V: 0 - 4 MHz @ 1.8 - 5.5V, 0 - 10 MHz @ 2.7 - 5.5V – ATtiny13: 0 - 10 MHz @ 2.7 - 5.5V, 0 - 20 MHz @ 4.5 - 5.5V

Industrial Temperature Range

Low Power Consumption – Active Mode: • 1 MHz, 1.8V: 240 µA – Power-down Mode: • < 0.1 µA at 1.8V
Rev. 2535JS–AVR–08/10 Document Outline Features 1. Pin Configurations 1.1 Pin Descriptions 1.1.1 VCC 1.1.2 GND 1.1.3 Port B (PB5:PB0) 1.1.4 RESET 2. Overview 2.1 Block Diagram 3. General Information 3.1 Resources 3.2 Code Examples 3.3 Data Retention 4. Register Summary 5. Instruction Set Summary 6. Ordering Information 7. Packaging Information 7.1 8P3 7.2 8S2 7.3 S8S1 7.4 20M1 7.5 10M1 8. Errata 8.1 ATtiny13 Rev. D 8.2 ATtiny13 Rev. C 8.3 ATtiny13 Rev. B 8.3.1 Wrong values read after Erase Only operation 8.3.2 High Voltage Serial Programming Flash, EEPROM, Fuse and Lock Bits may fail 8.3.3 Device may lock for further programming 8.3.4 debugWIRE communication not blocked by lock-bits 8.3.5 Watchdog Timer Interrupt disabled 8.3.6 EEPROM can not be written below 1.9 Volt 8.4 ATtiny13 Rev. A 9. Datasheet Revision History 9.1 Rev. 2535J-08/10 9.2 Rev. 2535I-05/08 9.3 Rev. 2535H-10/07 9.4 Rev. 2535G-01/07 9.5 Rev. 2535F-04/06 9.6 Rev. 2535E-10/04 9.7 Rev. 2535D-04/04 9.8 Rev. 2535C-02/04 9.9 Rev. 2535B-01/04 9.10 Rev. 2535A-06/03
Corebai - АЦП, ЦАП, ОУ, интерфейсы и другие аналоговые микросхемы поступили на склад