ЭФО предлагает со своего склада новую серию преобразователей интерфейсов USB UART компании FTDI FT232RNL-REEL

Datasheet LTC3772B (Analog Devices) - 3

ПроизводительAnalog Devices
ОписаниеMicropower No RSENSE Constant Frequency Step-Down DC/DC Controller
Страниц / Страница20 / 3 — ELECTRICAL CHARACTERISTICS The. indicates specifications which apply over …
Формат / Размер файлаPDF / 331 Кб
Язык документаанглийский

ELECTRICAL CHARACTERISTICS The. indicates specifications which apply over the full operating

ELECTRICAL CHARACTERISTICS The indicates specifications which apply over the full operating

Выбираем схему BMS для заряда литий-железофосфатных (LiFePO4) аккумуляторов

Модельный ряд для этого даташита

Текстовая версия документа

LTC3772B
ELECTRICAL CHARACTERISTICS The

indicates specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25
°
C. VIN = 4.2V unless otherwise noted. (Note 2) PARAMETER CONDITIONS MIN TYP MAX UNITS
VFB Input Current (Note 5) –10 2 10 nA Overvoltage Protect Threshold Measured at VFB 0.850 0.880 0.910 V Overvoltage Protect Hysteresis 40 mV Oscillator Frequency Normal Operation VFB = 0.8V 500 550 650 kHz Output Short Circuit VFB = 0V 200 kHz Gate Drive Rise Time CLOAD = 3000pF 40 ns Gate Drive Fall Time CLOAD = 3000pF 40 ns Peak Current Sense Voltage IPRG = GND (Note 6) ● 55 70 85 mV IPRG = Floating ● 120 138 155 mV IPRG = VIN ● 190 208 225 mV Default Soft-Start Time Time for VFB to Ramp from 0.05V to 0.75V 0.8 ms
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings dissipation PD according to the following formula: may cause permanent damage to the device. Exposure to any Absolute TJ = TA + (PD • θJA°C/W) Maximum Rating condition for extended periods may affect device
Note 4:
Dynamic supply current is higher due to the gate charge being reliability and lifetime. delivered at the switching frequency.
Note 2:
The LTC3772BETS8/LTC3772BEDDB are guaranteed to meet
Note 5:
The LTC3772B is tested in a feedback loop that servos VFB to the specifications from 0°C to 70°C. Specifications over the –40°C to 85°C output of the error amplifier while maintaining ITH/RUN at the midpoint of operating temperature range are assured by design, characterization and the current limit range. correlation with statistical process controls.
Note 6:
Peak current sense voltage is reduced dependent on duty cycle as
Note 3:
TJ is calculated from the ambient temperature TA and power given in Figure 1.
W U TYPICAL PERFOR A CE CHARACTERISTICS Quiescent Current (No Load) Quiescent Current (No Load) Quiescent Current (Shutdown) vs Input Voltage vs Temperature vs Input Voltage
225 250 25 VIN = 5V 220 230 20 µA) µA) µA) 215 15 210 210 190 10 205 QUIESCENT CURRENT ( QUIESCENT CURRENT ( QUIESCENT CURRENT ( 170 200 5 195 150 0 2 3 4 5 6 7 8 9 10 –60 –40 –20 0 20 40 60 80 100 2 3 4 5 6 7 8 9 10 VIN (V) TEMPERATURE (°C) INPUT VOLTAGE (V) 3772B G01 3772B G02 3772B G03 3772bfa 3
Электронные компоненты. Бесплатная доставка по России