Смарт-ЭК - поставщик алюминиевых корпусов LinTai

Datasheet OP97 (Analog Devices) - 7

ПроизводительAnalog Devices
ОписаниеLow Power, High Precision Operational Amplifier
Страниц / Страница9 / 7 — STANDARD. 5962-89544. MICROCIRCUIT DRAWING
Формат / Размер файлаPDF / 84 Кб
Язык документаанглийский

STANDARD. 5962-89544. MICROCIRCUIT DRAWING

STANDARD 5962-89544 MICROCIRCUIT DRAWING

39 предложений от 17 поставщиков
Микросхема Операционный усилитель, ANALOG DEVICES OP97EPZ Operational Amplifier, Single, 1 Amplifier, 900kHz, 0.2V/µs, ± 2V to ± 20V, DIP, 8Pins
Lixinc Electronics
Весь мир
OP97EPZ
Analog Devices
от 665 ₽
Maybo
Весь мир
OP97EPZ
Analog Devices
1 283 ₽
Augswan
Весь мир
OP97EPZ
Analog Devices
по запросу
ЗУМ-СМД
Россия
OP97EPZ
Analog Devices
по запросу

Модельный ряд для этого даташита

Текстовая версия документа

TABLE II. Electrical test requirements. MIL-STD-883 test requirements Subgroups (in accordance with MIL-STD-883, method 5005, table I) Interim electrical parameters 1 (method 5004) Final electrical test parameters 1*, 2, 3, 4, 5, 6, 7, 8 (method 5004) Group A test requirements 1, 2, 3, 4, 5, 6, 7, 8, 9 (method 5005) Groups C and D end-point 1** electrical parameters (method 5005) * PDA applies to subgroup 1, excluding VIO end-points. (No other subgroups are included in PDA). ** In accordance with table I, except VIO = ±50 µV maximum. 4.3.2 Groups C and D inspections. a. End-point electrical parameters shall be as specified in table II herein. b. Steady-state life test conditions, method 1005 of MIL-STD-883. (1) Test condition A, B, C or D. The test circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 1005 of MIL-STD-883. (2) TA = +125°C, minimum. (3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883. 5. PACKAGING 5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A. 6. NOTES 6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original equipment), design applications, and logistics purposes. 6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor- prepared specification or drawing. 6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
STANDARD
SIZE
A 5962-89544 MICROCIRCUIT DRAWING
DLA LAND AND MARITIME REVISION LEVEL SHEET COLUMBUS, OHIO 43218-3990 C
7
DSCC FORM 2234 APR 97
ТМ Электроникс. Электронные компоненты и приборы. Скидки, кэшбэк и бесплатная доставка