AC-DC и DC-DC преобразователи напряжения Top Power на складе ЭЛТЕХ

Datasheet LTC3721-1 (Analog Devices) - 4

ПроизводительAnalog Devices
ОписаниеPush-Pull PWM Controller
Страниц / Страница16 / 4 — ELECTRICAL CHARACTERISTICS The. denotes the specifications which apply …
Формат / Размер файлаPDF / 189 Кб
Язык документаанглийский

ELECTRICAL CHARACTERISTICS The. denotes the specifications which apply over the full operating

ELECTRICAL CHARACTERISTICS The denotes the specifications which apply over the full operating

15 предложений от 11 поставщиков
IC REG CTRLR PUSH-PULL 16QFN / Push-Pull Regulator Positive, Isolation Capable Output Step-Up/Step-Down DC-DC Controller IC 16-QFN (4x4)
727GS
Весь мир
LTC3721EUF-1#TRPBF
Analog Devices
от 39 ₽
ChipWorker
Весь мир
LTC3721EUF-1#TRPBF
Analog Devices
265 ₽
EIS Components
Весь мир
LTC3721EUF-1#TRPBF
Analog Devices
366 ₽
Augswan
Весь мир
LTC3721EUF-1#TRPBF
Analog Devices
по запросу

Модельный ряд для этого даташита

Текстовая версия документа

LTC3721-1
ELECTRICAL CHARACTERISTICS The

denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25
°
C. VCC = 9.5V unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
SSR Soft-Start Reset Threshold Measured on SS 0.7 0.4 0.1 V FLT Fault Reset Threshold Measured on SS 4.5 4.2 3.5 V
Note 1:
Absolute Maximum Ratings are those values beyond which the life
Note 5:
The LTC3721–1 is guaranteed to meet performance specifications of a device may be impaired. from 0°C to 85°C. Specifications over the –40°C to 85°C operating
Note 2:
Includes leading edge blanking delay, R temperature range are assured by design, characterization and correlation LEB = 20k, not tested in production. with statistical process controls.
Note 3:
FB is driven by a servo loop amplifier to control V
Note 6:
This IC includes overtemperature protection that is intended to COMP for these tests. protect the device during momentary overload conditions. Junction
Note 4:
Set FB to –0.3V, 2.5V and insure that COMP does not phase invert. temperature will exceed 125°C when overtemperature protection is active. Continuous operation above the specified maximum operating junction temperature may impair device reliability.
W U TYPICAL PERFOR A CE CHARACTERISTICS (TA = 25
°
C unless otherwise noted) Oscillator Frequency vs Start-Up ICC vs VCC VCC vs ISHUNT Temperature
200 10.50 260 CT = 270pF 150 10.25 250 A) µ (V) ( 100 10.00 240 CC I CC V FREQUENCY (kHz) 50 9.75 230 0 9.50 220 0 2 4 6 8 10 0 10 20 30 40 50 – 60 – 40 – 20 0 20 40 60 80 100 VCC (V) ISHUNT (mA) TEMPERATURE (°C) 372311 G01 372311 G02 372311 G03
Leading Edge Blanking Time vs RLEB VREF vs IREF VREF vs Temperature
350 5.05 5.01 300 TJ = 25°C 5.00 5.00 250 TJ = 85°C 4.95 200 (V) (V) 4.99 REF REF 150 V V 4.90 BLANK TIME (ns) T 100 J = –40°C 4.98 4.85 50 0 4.80 4.97 0 10 20 30 40 50 60 70 80 90 100 0 5 10 15 20 25 30 35 40 – 60 – 40 – 20 0 20 40 60 80 100 RLEB (kΩ) IREF (mA) TEMPERATURE (°C) 372311 G04 372311 G05 372311 G06 sn37211 37211fs 4
ТМ Электроникс. Электронные компоненты и приборы. Скидки, кэшбэк и бесплатная доставка